How do you feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely rocket science, however it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open up a wall to remove the old tub and also place the brand-new bath tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified on your own for the task as well as are comfortable trying it. Rather than hiring a professional to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you install a brand-new tub in your washroom if you have actually already purchased a new bathtub and don't require to alter the plan of your previous water system pipes.
Your tools and also product checklist must consist of the following:
Preparing for the Installment
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the versatile faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is detach the water system. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be quite troublesome because of the restricted accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub until the spirit level reviews degree.
To mount taps, fit all-time low of the furthest adaptable faucet port to the ideal supply pipe by making a compression sign up with; after that do the same for the other tap.
Switch on the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the tub and also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has been made use of at least once as this will settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers are in area between the faucet and also the sink. Secure the faucet in position with the producer given backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing complications with moisture as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the tub remains in use. The sealant can break relatively very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog entry about How to Install a Bathtub while doing a search on the internet. So long as you appreciated our blog post kindly do not forget to pass it around. Thank-you for taking the time to read it.
Fast relief, just a call.